Friday, March 18, 2011

T-33 1/48 Academy

Continuing my visit in the Belgian airforce, the next trainer aircraft on the to do list was the old and venerable T-33.
The model is Academy, I simply added an old True detail resin pit and the newly released  4+ decals


Straightfoward build, almost straight from the box safe for the cockpit and the scratched IFR hood for the backseat.
The paint is the usual beglgain SEA camouflage: H310, H303, H301 from the Gunze range.
All three have been post lightened with lighter colours. The underside colour is H311. The daygloo is Gunze as well





 
The model was completed in March 2011.

Wednesday, February 23, 2011

Making your own decals - 1/48 FM Fouga Magister


I'm often asked how I do custom decals, so I'll try to explain how I do it in step by step, using a 1/48 Fonderie Miniature Fouga Magister build as an example.
Here's the challenge: Nobody ever made 1/48 Belgian Fouga decals for the last part of the flying career of the birds.
Fonderie Miniature has a boxing with the Belgian Fouga but it seems to be for earlier Fougas and seems to be not quite correct anyway.

As far as I could check, Daco, the belgian decal specialist, didn't do any Fouga sheet either.
Since I have a Belgian Fouga to do - I need decals and since I have to make them myself, let's do one of the two last flying turtles, the most famous MT-35.

Prerequisite: What do you need?

  1. MANY picture of the real bird you are trying to make decals for. Airliners is usually a great source but I prefer to use my own pictures. When I go to air shows, I not only concentrate on the airplanes like everyone does but I snap pictures of the tiniest details on specific aircraft. Planning homemade decals starts right there. Take close-up pictures of logos, markings at a straight angle, without any perspective (or the least possible)
  2. Obviously a DAO software to create the decals and the basic knowledge to use the software. For many of us, that's where the problem starts. Well it is not easy. But it comes with experience, so if you never try, you'll never succeed. Decal work is usually basic features of those software so all motivated ppl should be able to start and get great results after a minimum of training with the software.
    I use photoshop, but paintshoppro and illustrator are two other suitable software.
  3. Blank decal sheets. White and transparent. You can find them in most hobby stores nowadays and although most were done for laser printers, we start to get specific sheets for inkjet printers.
  4. So obviously, you need a decent colour printer. I have a laser colour printer, but as said above, inkjet works great nowadays as well.
  5. a 3 view drawing of the bird you're needing decals for is welcome. But it has to be accurate to your model. Another way is to scan the parts real size. That will be used a s a template to check the decals height, length, etc etc.
  6. Your usual modelling tools and patience.

Let's get started with point 1, collecting pictures.

Here's the kind of pictures you'd need - those were taken at various air shows from 2007-2009 when the MT35 & MT37 Fouga were all over the place :)
They have been resized for the forum, but do keep them hi res obviously.
 
 
 
 
Well, I can post dozen of them, but I guess you have the picture already :)
Now, real images are great, but you'll need to be able to use those in your DAo software. And you need a starting point.
That starting point is a scan of the instruction sheet or any 3 views drawing of the airplane you're needing decals for.
In this very example I scanned Fm's instruction sheet where there is a nice 3views of the Fouga.
But before doing so, one small comment about resolution:
Decals can become quite small and you'll need a hi res image to be able to write small stencils in 1/48. So you need to ensure that your basic template is hi resolution. Usually computer images are 72 dpi (dot per inch) for decal work, i never work lower than 300dpi.
Wanna see why?

The next sample is a 2mm serial number, that's the one going on the wing fuel tank. The left picture is the 2mm at 300dpi and the right oine is the 2mm at 72dpi.
As you see the right one is useless. Conclusion, always work in hi definition for decal work. the smaller the scale the higer the definition you'd need.

Usually, 1/48 is minimum 300dpi. 1/32 could be lowered to 150dpi depending on the artwork.
That is important to start as early as possible with a 300 dpi file, so when your scan of the instructions comes out of the scanner, ensure you enlarge them to 300dpi (if you scanner couldn't print at that resolution) Even if the files so enlarged aren't very pretty, that's not important, as they are used only for template work...
Here's the scan of the FM 3 views drawing:

Sizing up the template with the dimension of your model.

Scanning a paper document, or using real pictures you took at airshows are all from different sized and they need to be set on the same reference so they can be used all together.
So you have
- a scanned 3views drawing at 300dpi
- your air shows pictures
- your model.

Obviously, the first step is to ensure that your 3 views drawing is the same size as your model!
Once again, that's easy. Or you used scaled drawings and they already are realsize or you need to adjust them yourself.

How?
in my scan above the Fouga wing measure 7.6cm length. My Fouga model wing in 1/48 is 10.3cm long.
So 10.3/7.6=1.355

Enlarge the 3 views drawing by a factor of 35.5% and recheck the distances of both wings, you should get something like 10.3mm on paper and 10.3mm on the plastic.

Sure the quality of your template isn't better, but who cares... :) the precise stuff comes afterward.
but this STEP is PARAMOUNT for the future of your decal work. If you realise later than you're not working on the same scale, you'll have to start from scratch.
that being said, I often print the WIP decal artwork and check them against the 1/48 model for accuracy and fine tuning ...
As for your air show pictures, they are usually hi res pictures, the kind of stuff you could print on a poster, so they will be always bigger than your 1/48 scaling down, so keep them at their native resolution, that's more than enough. We'll scale them down later anyway

The font problem:

Obviously, one of the main aspect of decal work is to use the relevant fonts.
Of course, it is quite possible to work with graphics instead of fonts but the good thing about fonts is that they are vectorized (while graphics are usually not) and that means that fonts can be decreased, increased in size without any quality loss. So for me, font use always has the upper hand on graphics.
Military fonts are usually well known and when doing some custom decals, you'll end up inevitably with a small collections of specific model fonts.
The most well known are:
  • Amarillo & USAF stencils for USAF
  • Longbeach for USN
  • Futura, USAfonts for general purpose
  • RCAF6 for Canada
  • Luftwaffe_fonts for german WW2 aircraft
  • RAFstd for RAF fonts
  • ... etc etc
Some are available for free, some are for sales. But usually it's easy to find them on the web, most of the time for free.
Coming back to the Fouga example, this presented some font challenges:

None of the two fonts I see there are usual model fonts and I have none of them.
I started my research by enlarging the above image to 300 dpi and to the real size of my 1/48 fouga (remember the wing at 103mm?) and typing the same text with different samples of fonts installed on the computer and there, luck striked!
The large commemorative wing marking is a normal windows font: Monotype Corsiva.


One problem solved.
The next one was going to be a little bit more complicated!

The aircraft code for the Fouga (in this case MT 35) are very special.
Google being my friend, I finally found that the belgian military don't have a font for the Fouga codes. They paint each marking individually from masks and that explains why no two fouga have the same font for their codes.
That obviously is a work for graphic code instead of fonts, but no - that's just not how I work, so I continued my font quest comparing different samples and came to the conclusion that one of the font I use often is very close to the MT35 font: Technic bold.

Many would find it close enough and I would agree. but the rounded edges of the technic font didn't hack it for me, so I decided to modify the font technic bold and create a specific font for the MT codes. To do that I use font creator, a small software allowing to create your own fonts, but that's outside of the scope of this tutorial.

Most of users would be pretty happy with using the technic bold font as it is, especually since when scaled donw to 1/48, the default are not that much visible anymore.
The rest would probably draw the MT codes in illustrator as graphics simply - which I reckon is my second best choice.
Anyway, here's the ongoing work on the fouga font: below is a picture of the code, in the middle is the technicbold and on top is the homemade foga font.
Not there yet, but we are close.

The final font problem was for the smaller serial found on the wingtip tanks and at the rear end of the aircraft. This while easily found on google while researching the MT code issue; It's a free font called Phantom_stencils.

With the font issue solved for now, let's move on to the logo and graphics needed for the decals
Beside the letters and numbers, we'll have to deal with many different things like the turtle logo, the rescue arrows, the flags and eventually the stencilling.
Well, obvioulsy, use your decal scratch box as often as possible and whenever possible, but if you don't have the relevant decals, well you can always create your own.
In this case, the turtle, wolves, rescue arrows, step lines will be created on the homemade decal sheet.
When you have the luxury to have good pictures, it's again easy with a minimum of photoshop work:
Let's have the turtle as an example:


Open the image in photoshop and start by simply removing the background colour with the magic eraser tool:

That will remove the silver grey from the picture the two arrows on the above image point sto the magic eraser tool and the tolerances you need to apply to have all the background removed at once, while keeping the details in the other colours. The process is rather simple but sometimes you may have to proceed in multiple steps. Don't be overly concerned with noise remaining after the operation, the logo will be further reduced.
Once you're satisfied with the result, copy and paste the logo into your 3views drawing. That's where the logo will be scaled down and placed on it's correct location:

Obviously, you'll need to use photoshop layers for such new graphics. that will ensure that the turtle remains independant from the rest of the layout and can be moved, resized etc without influencing the rest of the image.
The yellow rescue arrows could be created the same way but they are better done with the line tool.
Insert the reference picture over the 3D view, scale it down so it match the template.
select a yellow colour (always use darker than the reference colour, i'll come back to that later) and select an arrow to be drawn at the end of the line.
The next step is to choose the correct line width, matching the arrow in the picture. No secret there, you'll have to try until you find it. Same is true for the geometry of the arrow.


Let's now have the rescue text in there
Select the text tool and a black colour. Select the Phantom stencil font and type RESCUE
Size accordingly and then rotate the whole along the inside of the newly created yellow arrow.


Repeat the whole process for the second arrow.

The wolves on the tail are done with the same method as the turtle logo. The flags can be made as well or can be painted.

The dreaded white problem

Most printers can't print white because most of the paper we use for printing is white. So unless you have an ALPS printer, you can't print white on a transparent decal sheet.
That is obviously a problem for white drawings, but also when you need to design a clear colour decal that will go on a dark coloured model. Like a yellow rescue arrow on a SEA camo.
Well the solution to that problem is to buy a new stock of sharp scalpel blades, because you are going to need it.
Indeed, the only "easy" solution is to print your artwork on a white blank decalsheet instead of using a transparent one.
Doing so you will provide your artwork a dense white coat as a base which will hopefully provide enough blanking against your dark paint.
The problem is that you will have to cut very close to the edge of your artwork once the sheet is printed to avoid white edges on your decals... That should be easy for the rescue arrow, but it sometimes near impossible to do on more complicated designs.
Another possibility, when you don't have a white decal sheet or when you really can't cope with scalpels, is to paint the area where the model must go in white on the model.
Again, that's easy for some things, and impossible for others.

So if you have to do this, you'll have to split your artwork in two separate prints. One on a transparent decal sheet, the other part on a white decal sheet.
No need to make your life harder by printing black letter on a white backround and have to detour them before applying to a green camouflaged model
That's why it is advised to always have both kind handy.

In the case of the Fouga, i didn't have too much concerns as the prevailing aluminium colour should be light enough to allow the yellow of the rescue arrow to be visible. It might have been a problem for the belgian roundels but luckily, i'll be using roundels from another belgian aircraft decal sheet.
The flag on the tails on the other hand will be prepainted white on the model, before the transparent printed decal sheet is applied.
The turle has some white spots, but I won't be concerned with those and i'll let them transparent, so the whole decal sheet can be printed on the transparent decal.

So usually a mix of different techniques is required to overcome the lack of white in our printers. Ultimately, get a friend who owns a ALPS printer, that works quite good as well wink.gif

Blank fitting

Once all the artwork is done, I usually then print the whole decal sheet on normal paper and I run some tests on the model to check scale, distance, ...
That is particularily useful when you're trying to design a decal that goes along panel lines, like the no step area on the flaps on the Fouga for instance.
It was also worth checking the height of the MT35 serial and the flags for the tail to ensure that the white painted area would match.

I usually do this on a cleanly assembled model, prior to any painting.

That's also when I decide which decals will stay together on the same piece of film or which ones needs to be separated.
I this case I rearranged all the decals on the left nose so I could use one bigger piece of film instead of multiple small ones. The black vertical lines needed to match the feet recess in the fuselage

Back end seems fine...

Printing the decals

At this stage, I just close the computer and enjoy some airbrushing on the model :)
And eventually I'll grab my courage with both hands and after numerous last change and many draft prints on white paper, I finally place the expensive decal sheet in the printer (and pray that my wife doesn't send something in the queue from her own computer to the networked printer :) ) and I send the image to the printer.

That's what comes out of it, it's blurred ok, but that's my photography skills, not the artwork :)
Don't let the freshly printed decal too long without protection. I usually very quickly coat the whole decal sheet with two or three very thin coat of clear varnish.
I use whatever varnish I have on my hand, usually X22 acrylic from tamiya or H21 from Gunze.
I tried also microscale liquid decal film, but I had mixed results when sprayed and I reverted to plain gloss acrylic varnish.
Then I let it dry for a rather long time.

So the Fouga is now painted, gloss coated and ready for the decals.

The homemade decals are usually more fragile than the commercial ones . See the damage in the last of the many print ?
Depending on your amount of gloss coat on the sheet, they might also be very thin or very thick ! you decide there.
Care should be taken when you cut the decal sheet not to attack the decal itself.
When your decal is quite thin, you might ruin it by cutting too close from the artwork. But on the other hand the edges are thin and transparent  so you can take an extra security margin by cutting an extra millimeter from the artwork, it will remain invisible on the model.
If it's thick, you can cut closer but you risk seeing the film on the finished model.
As always in modelism, you have to find the right balance.
The rest is decalling as usual. Applied on the glossy surface, they go very well and react nicely to microsol and set. Then they are protected with another coat of gloss before weathering.

Final result:

Here's the finished result, hopefully this tutorial will illustrate the fact that anybody can give it a shot and start doing his own decals...


I finally decided to discard the big red text on the wings.


And the decal sheet, realsize in 300dpi

PDF version for those interested:
http://www.ravico.com/ST/models/Fouga_decals/decals_fouga_FINAL.pdf

Model completed in February 2011.

Thursday, September 23, 2010

1/48 Belgian resin Marchetti

I always have loved that airplane and I have a soft spot for the yellow paint the belgian airforce use for basic training. So when a friend asked me to build the aircraft he soloed in, i decided to build the military version at the same time.

Both models are resin but from different origin.
The military is the old Skymodel and the civilian is from planet model in cooperation with CRP modelling. The planet model (CRPO) version is crispier and more modern. It's by far the best of the two version.


As often with resin models, it isn't for beginners.

The sky model came with two left wings so I had to convert one of the two left wing to a right wing, the vac canopy is far from transparent and just doesn't fit the fuselage, the parts were bent, wing angle was flat, most of the parts are undersized - especially the wingtip tanks etc etc...

The planet model on the other hand was a joy to build with perfect fit and accurate shapes and wonderful decals. the canopy is clear and fits perfectly. the only problem I could find on that one was the wing angle too flat as well, but that was easily corrected with a bit of boiling water :)

When placed alongside each other the differences in shape and size are striking !!!
They will need to be stored away from each other!

 




Both were completed in September 2010.

Sunday, June 13, 2010

1/32 Su-27 Flanker


I'll use the following goodies on that Trumpeter 1/32 Flanker B, first mould
- Mastercasters Russian pilot and Su207 wheels
- Zactoman intakes, nose and canopy correction
- Lindenhill decal & stencils
- Eduard prepainted cockpit set and exterior set
- Quickboost seat and frontpanel glareshield.
- Aires exhaust set.

The idea is to display that huge bird braking on the runway on the landing roll.
Airbrake will be popped out, nose wheel compressed, pilot at the controls and canopy closed of course.
The big challenge of this build will not be the aircraft itself but the brake chutes I intend to deploy... I don't know at what stage yet :)
I'm just out of a few days fighting hard to make two 1/32 resin figure fit in a Skyhawk cockpit, and I was ready to start back with this one. But nada, the mastercaster pilot fits in the Su27 cockpit like a glove. Even the feet nicely rests on the rudder. Very well done MasterCaster, that figure is great.

I debated using the kit seats or the quickboost and finally chosed to scrape the belts from the resin seat and use that one. the figure fits both the same way.
Of course since a modeller can't be totally satisfied, the pilot doesn't have his hands on the control and that will need to be modified. I borrowed 2 arms from a US pilots to see if it would fit with minor surgery. that US pilot is huge so the arms are a bit long :)

The next step was to try the seat &pilot into the canopy and up the fuselage

And then close the canopy to see if I have enough clearance...

Yep, works ok. The IRST structure on the coaming prevent the canopy to close fully, that will be addressed later. The zacto vacu canopy was not so hard to cut to shape (always a stressfull moment) and it's also a great fix for the kit.
First time I use prepainted cockpit. It's quick and it's nice :)
Cockpit colour is aeromaster 1101 french blue. It matches perfectly the eduard colours. too bad we can't find that one anymore.

The assembly started with the intakes and they are a real pleasure to work with. the fit is perfect and the resin is very nice to work with. never had I the pleasure to work with such a nicely crfated and designed aftermarket product. I'll raise the FOD guard so I don't even need to sand the two halves of the intake trunk.
Painting was done with a beige colours inside, FOD guard are dark metal. and the lips are fuselage colours.
 

The level of details on those intakes are flabbergasting. I wouldn't buy any flanker without them for sure. I won't spend a lot of time into the wheel wells - I know they lack a lot of details and tubing but I'll concentrate on what is really visible.

From analysing it's a rather easy model to build. It doesn't have many parts nor complicated assemblies. But it has some rather nasty traps.
Most of the time on this one is not spent on building but on the web looking for pictures and built reports to identify and see how to avoid them. I'll get on this back later
In the meantime, minor detailling was done in the gear bay and the intakes were glued in place.
 

It's nowhere close to what has been seen on some previous build and rather harsh, but enough for me there. Most of those aren't visible anyway. I just added the rear box and fuel pipes (yellow)
Again, it's really not laid out as it should be, the idea was just to populate the area with yellow pipes. I also added the two exhaust aft of the wheel bay. Easy enough to do.
 

the other side doesn't have the fuel pipes but some sort of pump and a few green pipes. Nothing fancy. Of course the real one has 4 parts, mine has 3. A bigger exhaust was also fitted aft of the wheelbay. The nose bay is from the box. I decided to paint the gear bay a mix of hemp and grey/blue. The contrast look nice and I saw that on many pictures.

The intakes tend to bent a bit the lower fuselage when they are glued on. Something that will need careful handling when the fuselage parts are glued together.
I almost blew it on the port intake because the end of the resin fan wasn't sanded enough and prevented the intake to fit perfectly.  My contact points between the lower fuselage and the front part of the intakes is also very small and that may cause problem later on in the build ...

I'm about ready to close the fuselage together.
The first trap to avoid is gluing the wing on the bottom fuselage and relaise that you have a step between the wing and the top fuselage. Something very hard to fix. Many guys glue the wing to the upper fuselage before closing it and I must say I'll do the same. Although Zactoman identified the problem and showed us where to sand the upper fuselage to avoid the issue.

Second trap is to avoid screwing too hard to nose screw as this will distort the front fuselage and probably create problems fitting the nose cone.

Third trap here is to make sure to study the tailerons as their pivot point isn't placed correctly and may need to be solved before closing the fuselage if you want to make it perfectly. I think that in my case I'll simply replace the pivot point after. I won't superdetail the area but I need to place them in the braking position, so I'll have to change the pivot point anyway.

Another trap to avoid: Nose fitting:
Better follow Zactoman instruction and remove a bit of material before closing the fuselage ...
The fit isn't perfect on the sides and since the plastic is very thin around the nose, you run the risk of sanding through ...

Apart from the nose, no big fitting issues and very few putty used.
 
First tests with the colours:
painting a Su27 is not easy. actually painting it is, choosing the colours is not :)
I finally decided to make my own mixing based on adversary  blue colours.

Pale blue FS35526 = 1xH45 + 2xH308 + 5xH11
Blue FS35190 = 5xH11 + 1xH308 + 1xH322
Haven't decided for the grey which should be something like H306, 307 or 308

 
 
 
 
Of course all this will be lightened up and faded in at a later stage. and I'll probably make darker fresh paint touch ups, especially with the dark blue.
 
The grey is on: H308 was chosen.
fading part 1:  inside of the panels with base colour + white
at least for the grey and blue.
 
 
 
Part2 of the painting was completed and the green dielectric is on as well.
I'll probably blend the colours together with a mist of pale blue now to give it less contrast - although the flash pictures give more contrast than there actually is on the real model.
the varnish and future weathering will blend the colours as well, but I'll try the pale blue mist first and see how it goes:
 
 
 
Here is the blue mist: The picture don't make them justice but the result is much better now
 
 
Then I painted the large exhaust areas. Nothing fancy. Some  different alclads here and there and a first try with the new Alclad Hot metal blue which is very nice although I'm sure tamiya clear blue would do the same.  Lots of masking on those. I tried voluntarily to make some tiny paint spots randomly with the airbrush by starting on the model instead of beside it. Nothing of that is quite controlled painting :) Interesting for a first try in the dark side.
This will do for the time being - they will be further weathered at later stages.
 
Primer yellow into the airbrake and slats and i'm about ready to work on the cockpit and gears.

Before and after the light blue mist.. just testing, comparing ...
although i've got some nasty flash reflection in the greys... first time I use flash for those kind of pictures, sorry!
 
Some wheels problems ...
I have the kits wheels and Mastercaster's wheels. Main wheels, no problem. Mastercasters wheels are flattened and seem a bit less bulky than the kit's. The great advantage is of course that you avoid that rubber
 
 
But the problem I face is with the smaller & flatened Mastercaster nosewheel. When the Mudguard is placed (both original and Eduard's) the rubber part of the noseguard is actually lower than the flat of the resin wheel.

That's for whatever compression of the nosestrut. 
At first I was very appealed by the springs in the wheels struts. But I lost one anyway :)
I'm doing a braking airplane, so the nosewheel strut will be compressed and thus I assembled the nosewheel without spring (but still moveable and reaching all position - I'll glue it later on.)
The two remaining springs have been inserted into the main gear but it's not a good idea in the end. The spring are too strong and don't compress with the weight of the model, the consequence is that the model sits too high on its main wheel. I'll remove the springs and I'd advise to get rid of them and glue the struts at the required level (and equal on both side).

I also elected to work with the palstic main gears as the Y supports are placed too high and need to be lowered on the legs. Easier done with the plastic than with the white metal.
Next step, detailling all those gears. They are way too crude!

 
Progress is slower as I work on some smaller details and start to think about the canopy.
Painting the inside of the gear doors. Nothing fancy. Then populating quickly the main gears. All this still need to be weathered.
 
 
The flaps normally needs to be cut, but I decided to do that with paint inside of actually cutting in the plastic. Weathering still need to come there as well.
 
The next issue will be fitting the closed canopy. I guess it was designed to be placed open, although you need to separate the windshield dor that. When you place it closed, the frames of the canopy are not wide enough and care must be taken to align the frame with the fuselage correctly. No big deal, some guides will be placed. I intended to use the internal canopy frame for that but it seems it is not wide enough either.
So first dryfit and see all the different component behave together, we have eduard, Trumpeter, Zactomodels, Mastercasters and Quickboost parts in there!
The forward looking tiny camera on quickboost glareshield was lowered as it sits a bit high for the vac canopy.
As you can see, I glued the vertical canopy frames on the fuselage, this is actually the best guide for the vac canopy.
 
The pilot is perfect! I just need to lower a bit the seat and lower the right hand so the stick gets lower in the pit. The biggest challenge there will be to fit the oxygen mask withouth destroying it. I need to empty the inside so it fits the pilot's face. The Hud was decreased in height, but as you see on the next picture, I have a conflict between the top rear view mirror and the HUD. I had to lift the mirror for the time being.
 
Next the vac canopy was fitted. this will be a major challenge to get right - especially without the use of cyano. The rear resin frame is bugging me because not wide enough but I'll back it up with small guides along the rims.
 
 

Piotr is strapped in and ready to go in the cockpit, some minor stuff to finish but he's basically ready.
 
 
 
I used foil for the harness and PE buckles. the stick was cut and glued to his hand and his other hand goes on the throttles, it was just sanded flat against the wall.  It fits just nice the flanker cockpit.
 
Piotr is finally in his cockpit. This was by far (up to now) the most challenging moment of this build.
Fitting the zacto canopy in a closed position. the cockpit frames are not wide enough and that creates a step between the canopy and the fuselage. This was overcome by placing some guides on the inside of the canopy and although all was successful when dryfitting, it went bad when gluing. I had to spend a full week end sanding and filling the canopy. Unfortunately, the vacuformed plastic doesn't sand very well. And care must be taken not to slip into the clear parts ... This will be a big surprise when I remove the masks.
 
 
Once satisfied with the fitting of the canopy, I could finally respray the canopy area and some touch ups in a darker blue as often seen on line birds. It gives a lot of life to the model, so far I'm pretty happy with it.
 
 
 
 
 

And finally some AA weapon candidates. Those are straight from the box, not sure if I'll use them or not.... ?  We seem them very often without any AA weapons,  but that's a bit naked isn't it ...
 
Decalling done, I'll need to thame a bit those red decals with a blue mist.
 
Here's the first draft of the parachute. From studying the picture, I came to the conclusion that the brake chute should be made of 5 squares of 225cm each. That makes a total height of 6.75m
Each square is subdivised in squares of about 32cm, delimited by the parachute lines crisscrossing.
In scale, that makes a parachute 21 cm long and high, made of 5 squares of 7cm. each crisscrossed by lines every 1 cm.
The center square has two extra lines in the center and the outer squares are cut in their longitundinal axis, but the lines remain there ...
okay, okay, that makes it a little bit complicated, so here's a sketch:
 

 
The Flanker is landing !
 
At least it's done ...
The parabrake strings were done with fishing wires instead of metal and although it was a long lasting job, it gave much better results :) Those two parabrakes are the hardest thing I ever did in my modelist career!
 
 
 
 
 
 
 
There are many impressive buids of Flankers out there - I used a few of them for references such as the one from Geedubelyer , Mr Narita, Flankerman, Wasserfall, Fancherello, ...
I consider the guys I quoted above master in their branch and I'm grateful they document their work so that guys like me can steal their ideas and have the same kind of fun. many thanks gents !!
 
Model completed June 13th, 2010